Splitcoaststampers.com - the world's #1 papercrafting community
You're currently viewing Splitcoaststampers as a GUEST. We pride ourselves on being great hosts, but guests have limited access to some of our incredible artwork, our lively forums and other super cool features of the site! You can join our incredible papercrafting community at NO COST. So what are you waiting for?
I just received a Die from Lawn Fawn called Puffy Cloud Borders. The three dies are attached by little "nibs". I was wondering if I'm to use them as is, or if I'm supposed to cut them with scissors. I never encountered dies like this before. Do I use regular scissors or a special pair. I have a pair of scissors that cuts rubber but nothing else. Thanks for any help you can offer.
Another hint for you....make sure when using the snips that you hold the dies close to flat surface (like the table top). These dies can fly off. It can take a long time to find that missing die when goes on a flight. Ask me how I know....
I cut apart the majority of my dies but I have a few sets that are a bunch of small pieces and I leave them attached to each other. I just put paper on the one image I want. I figure that I might not loose one if they are attached.
I use my button shank remover because I can get really close to the die to make the cuts.
Another hint for you....make sure when using the snips that you hold the dies close to flat surface (like the table top). These dies can fly off. It can take a long time to find that missing die when goes on a flight. Ask me how I know....
After I snip the ones I need they are placed on a magnet sheet and into an Avery Elle pocket for storage. If I have a stamp set that matches put that in the same pocket.
__________________ Mary Jo
prairiepapercrafter.blogspot.com
I use my button shank remover because I can get really close to the die to make the cuts.
Off to Amazon to buy a button shank remover. Thanks!
P.S.: I ruined a pair of good scissors the other day because I was too lazy to go into the garage and look for wire cutters or something else to use. I've learned my lesson.
This is brilliant.............I'm going to do this from now on!!
I use this trick when working with anything I don't want to lose, too. It was a lifesaver when I was putting the tiny screws back in the battery cover of my grandson's remote!
My boyfriend has some sort of snips that he uses to separate the ones I get. He saw me one day trying to separate some and was concerned about the sharp points. So he took over. Now I just hand them over to him when he is at my house and he takes care of them for me. :o) He uses some sort of snips for metal and a file.
I have a few tips. Many may be repeats as I don't have time to read all the posts.
You want to buy some flush cutters also known as wire snips. Regular cutters won't cut as close as flush cutters. Make sure the flat Die is against the Die.
don't use your expensive jewelry snips, buy a cheap pair just for dies. Dies are steel and much harder than jewelry wire. You will nick and dull your good snips.
I find that it helps to cut the metal twice, once close to each die. In fact, I actually nip the metal with my snips on the Die itself. They tend to slide a bit so if you overlap the edge of the Die a bit, you will get the closest cut. Sometimes I don't need any filing at all the the edge is near perfectly smooth.
If the angle of the cut isn't ideal and your snips don't fit, rather than snip in the middle or bending them back and forth to separate, try twisting one Die a quarter turn. Sometimes you can get your snips in better that way. And doing all the easiest, most accessible cuts of a large bunch of dies can help too.
Use a fine diamond file to get rid of the nubs. You can get one for about $6 CAN at any hardware store. Save it for dies only and don't use it for jewelry as it will dull more quickly just like the snips. I hold the file in my non-dominant hand and my Die in my dominant hand. I move the Die back and forth on the file rather than the file back and forth on the Die. It helps the file not slip off the edge of the Die and hurt your fingers. Also the Die is smaller so you have more control.
Consider keeping tiny dies together. You can always save the extra pieces or cut a scrap just to the size of the Die you want to use. Of course some dies come with smaller ones inside of larger ones so they have to be separated.
So glad this question was asked...I started purchasing dies from other companies (other than SU!) and a lot of dies come together...I've ruined my scissors trying to cut apart the dies...will look into the wire snaps or the button shank remover, as well as the fine diamond file. Thanks, very helpful.