Emboss Resist Etching

9 1/2" glass dessert plate or other flat surfaced glass

1/4" circle punched from dark cardstock

Scotch™ Tape

Coluzzle© cutting system

Adhesive-backed (Contact™) shelving paper

Glass cleaner spray

Paper towels

Embossing Buddy™

Rubber stamp(s)

Versamark™ pad

Embossing powder (any color)

Embossing heat tool

Rubber or latex gloves

Armour Etch Cream™ available at local craft stores [ buy it ]

Sponge wedge or foam brush

Scraping tool of some sort

Kitchen timer or clock

Step 1.
Attach the 1/4" cardstock circle to the center of the plate's eating surface with Scotch tape. There's no need to measure to find the exact center. This dot will be removed later; it is a guideline for stamp placement.

Step 2.
Clean the back side of the plate thoroughly with glass cleaner and a paper towel. Any fingerprints are a glass etcher's biggest challenge so keep the etching surface as clean as possible.

Step 3.
Using the Coluzzle circle cutter, create a frame from a piece of Contact shelving paper, using the largest cutting ring of the circle template. Discard the center piece.

Step 4.
Affix the frame to the back side of the plate, using the dot as a centering point. The glass etching cream will be applied inside this framed area, make sure it's pressed down well with no gaps or air bubbles along the edges by running a finger around the inside edges of the frame.

Step 5.
Gently clean the area inside the frame with glass cleaner and a paper towel to remove any fingerprints.

Step 6.
Swipe the Embossing Buddy across the framed area to reduce static and the slippery-ness of the glass when you stamp.

Step 7.
Ink the stamp of your choice with Versamark, and carefully stamp in the center of the framed area using the taped dot as your guide. Glass is slippery, so use a steady hand.

Tip: If a mistake is made, repeat steps 5 and 6.

Step 8.
Apply any color embossing powder to the stamped image. The color does not matter as it will get scraped away at the end.

Step 9.
Remove excess powder with a small paintbrush if necessary.

Step 10.
Use the embossing heat tool until the embossing powder is set and shiny. This takes a while to heat set because glass is much thicker than cardstock. If you're not sure it's done, heat some more.

Caution: Take care and avoid scorching the edges of the frame. Do not hold the plate while heating; the glass gets very hot.

Tip: If a mistake is made, repeat steps 5-10.

Step 11.
Pour a large blob of etching cream into the center of the contact paper circle frame.

Caution: Armour Etching Cream is caustic to skin so wear latex or rubber gloves just to be safe. The cream smells like rotten eggs, so work in a well-ventilated area.

Step 12.
Using your sponge wedge or foam applicator, lightly brush the cream right to left, and then up and down to ensure even coverage.

THICK coverage is key, and you can go over the inside edges of the frame. If you make a mistake, wipe it away quickly with a damp cloth. This cream begins etching very quickly!

Step 13.
Set a timer for 5 minutes.

Step 14.
When the timer goes off, go to the sink. Rinse the plate very thoroughly with warm water, rubbing slightly with a gloved hand or a clean sponge. Keep rinsing until no white cream remains. Discard the frame. Remove gloves rinse a little more, making sure no residue is left on either side of the plate. Scrape embossed image with a fingernail, wooden spoon or a plastic scraper.

Step 15.
Remove tape dot and dry with a clean cotton towel.

Any unetched areas can be touched up by applying a small dab of etching cream with a toothpick, waiting 5 minutes and rinsing again.

Note: Etching cannot be reversed. If there was cream in places where it shouldn't have been, it can't be repaired.

Step 16.
Completed project.