Splitcoaststampers.com - the world's #1 papercrafting community
You're currently viewing Splitcoaststampers as a GUEST. We pride ourselves on being great hosts, but guests have limited access to some of our incredible artwork, our lively forums and other super cool features of the site! You can join our incredible papercrafting community at NO COST. So what are you waiting for?
I think I posted this previously - some time ago, but don't recall the replies. Going thru my stash, I ran across my Xyrons and would like to try using them again: I have the Xyron 150 sticker maker and the Xyron 2.5" create-a-sticker. My problem has always been the excessive glue around the edges on any item I have run through either machine. I see you tube videos where the crafters just "'rub off" the sticky around the design, but mine never comes off and usually tears the die cut especially on intricate words. A friend suggested I have a bad roll of adhesive, but I have the same problem on both machines - and I have replaced the adhesive on the smaller one and have the same issue. I have been hesitant to buy the larger roll thinking I'd be wasting my money. Any suggestions as to what I am doing incorrectly? Thanks to all !
I use the tip of my bone folder and burnish all edges of the die before removing the top clear layer. For intricate dies you might need something with a finer tip.
The following 3 users liked this post by basketdiva:
I can't seem to remember to add sticky to intricate dies before I cut it so Xyron has been a life saver. After running through the Xyron, I place it face down on a foam mat (like a stamping mat) and burnish like crazy with the flat edge of above folder. Any remaining sticky I remove with an adhesive eraser.
Mary Beth
The following 2 users liked this post by lutheran:
wow - thank you all for the suggestions. Now that I read it (again), I think the 'solution' was to run the cardstock thru the Xyron first, and then cut.
Mac, I don't know of any other way to do it. The term 'sticker maker' is misleading, I think. Xyron's directions for the tiny model say to 'insert item, pull through, tear & peel sticker.' WHAT??
I have the 2.5 and 5", now, but really hesitated to buy one because I couldn't understand why I should have to cut out the item first if it's a sticker-maker!
I ALWAYS run the cardstock through the Xyron first, then die cut the item. If I'm doing a lot of the same card I run through a half sheet of cardstock, then I have enough ready to go. I save any unused pieces of all the colors I have. There is less waste of the cartridge with the 5" machine.
The following 2 users liked this post by harvestmoon:
I agree with the above comments - use the Xyron to make sticky paper THEN die cut. I gave away the small X-shaped Xyron because it didn't seem to work as advertised. But the next size up is one of my favorite tools now. I have been adding a lot of die-cut words to my cards, and it is a game-changer.
__________________ Cheryl "Mom" to Jazz & Cubby bungalowdays
Hi Mac,
I had so much trouble with the small Xyron adhesive runners, I ended up giving both of them away. However, Xyron makes an excellent adhesive eraser that I use for any adhesive that lands where it isn't supposed to be, you might give that a shot.
I just quickly draw around the edge of the design with a pen or pencil tip before removing the top layer of film and I don't have any problems with it after that. I love using the small X-shaped Xyron for little tiny things. If I have two designs with smaller ends, I just put those small ends in next to each other so they don't overlap and run it through to waste less.
__________________ Brenda
<-My sibling kitties, Milo and Rousseau
While I have 2 sizes, I use the small X-shaped xyron the most for making small stickers from a variety of border punches. Tricks I use are (1) burnish like crazy, using a piece of an old t-shirt; (2) use the sticky eraser; and (3) if any leftover stickiness at this point, use the EK Success powder brush (purchased many years ago, it holds a small amount of baby powder & has a brush tip you move over the sticky area. Sticky spot picks up the powder, which becomes invisible--and no more issue!) If this is no longer available, I think a small watercolor brush dipped in baby powder would be a good substitute.